Camber thrust

Camber thrust and camber force are terms used to describe the force generated perpendicular to the direction of travel of a rolling tire due to its camber angle and finite contact patch.[1][2][3] Camber thrust is generated when a point on the outer surface of a leaned and rotating tire, that would normally follow a path that is elliptical when projected onto the ground, is forced to follow a straight path due to friction with the ground. This deviation towards the direction of the lean causes a deformation in the tire tread and carcass that is transmitted to the vehicle as a force in the direction of the lean.[2]

Camber thrust is approximately linearly proportional to camber angle for small angles.[2][4] Bias-ply tires have been found to generate more camber thrust than radial tires.[3] Camber stiffness is a parameter used to describe the camber thrust generated by a tire and it is influenced by inflation pressure and normal load.[3] The net camber thrust is usually in front of the center of the wheel and so generates a camber torque or twisting torque.[2][3] The orientation of this torque is such that it tends to steer a tire towards the direction that it is leaned.

Contents

On bikes

On bicycles and motorcycles, camber thrust contributes to the centripetal force necessary to cause the vehicle to deviate from a straight path, along with cornering force due to the slip angle, can be the largest contributor,[1] and in some cases is the sole contributor.[2] Camber thrust contributes to the ability of bikes to negotiate a turn with the same radius as automobiles but with a smaller steering angle.[1] When a bike is steered and leaned in the same direction, the camber angle of the front tire is greater than that of the rear and so can generate more camber thrust, all else being equal.[2]

On automobiles

On automobiles, camber thrust may contribute to or subtract from the total centripetal force generated by the tire, depending on the camber angle. On a well-aligned vehicle, camber thrust from the tires on each side balances out.[5] On a surface rough enough for one front tire to momentarily lose traction, camber thrust from the other front tire can cause the vehicle to wander or feel skittish.[5]

See also

References

  1. ^ a b c Foale, Tony (2006). Motorcycle Handling and Chassis Design (Second ed.). Tony Foale Designs. pp. 2–23 to 2-26. ISBN 978-84-933286-3-4. http://books.google.com/books?id=84hF-qoR5I8C&printsec=frontcover&dq=Motorcycle+Handling+and+Chassis+Design. 
  2. ^ a b c d e f Cossalter, Vittore (2006). Motorcycle Dynamics (Second ed.). Lulu.com. pp. 47–48. ISBN 978-1-4303-0861-4. http://books.google.com/books?id=rJTQxITnkbgC&printsec=frontcover&dq=motorcycle+dynamics#PPA47,M1. 
  3. ^ a b c d Wong, Jo Yung (2008). Theory of ground vehicles (Second ed.). Wiley. pp. 40–43. ISBN 978-0-470-17038-0. http://books.google.com/books?id=LH8wd8im13AC&printsec=frontcover&dq=Theory+of+ground+vehicles+By+Jo+Yung+Wong. 
  4. ^ Pacejka, Hans B. (2006). Tyre and vehicle dynamics (2nd ed.). SAE International. pp. 162. ISBN 978-0768017021. "For small angles, the camber thrust is approximated by the product of the camber stiffness and the camber angle." 
  5. ^ a b Puhn, Fred (1981). How to Make Your Car Handle. Penguin Putnam. p. 87. ISBN 0-912656-46-8. http://books.google.com/books?id=cr4IyD5l1NQC&printsec=frontcover&dq=How+to+Make+Your+Car+Handle+By+Fred+Puhn.